CDQ-A脈沖點火棒使用說明

CDQ-A脈沖點火棒是根據石化、冶金、玻璃、陶瓷、工業窯爐等行業的需要，采用先進技術而設計生產的一種便攜式點火棒。本產品結構設計新穎、方便靈活、體積小、重量輕、點火安全可靠、火焰大小可調、壽命長、攜帶方便、不受環境、距離的影響，是一種理想的便攜手持式點火裝置。

一 ：技術參數

1 電源   1#電池3節

2 火花能量:1～2J

3 脈沖頻率：交流高頻

4 使用燃料：燃氣

二：結構及長度

電子棒直徑φ40mm 長度350mm 點火桿長度根據用戶需要待定

三：使用方法

1、使用時，先將電子艙電池蓋擰下，將3節1#電池按極性裝入電子艙內，電池正極向內，并擰緊電池封口蓋。

2、點火時，將點火棒點火頭對準點火部位。先打開電源開關，開關指示燈亮，按住按鈕開關點火，當燃氣被點燃料后，放開按鈕開關，停止點火，立即取出點火，并關斷電源。

四：注意事項

1如點火時，點火頭不打火，可能是：

a. 電池未接通  

b. 點火棒電極位置偏移，重新調整一下電極位置，兩極間隔調整為2.5～3mm為好。

2、點火棒內配的電池為優質1#電池。當電池使用一段時間后電量不足，影響點火，應及時更換優質新電池。

3、點火棒使用和運輸時，輕拿輕放，以免損壞。